While cleaning out the attic (a New Year’s resolution, perhaps?) you come across a pair of your grandmother’s old chairs. You realize that with a fresh coat of paint and new fabric, you can breathe life back into them – and they would be perfect for your home. Congratulations, you have just found your next DIY project!
Good Bones Are Good Bones
Furniture left languishing in attics and storage closets just needs a little TLC to bring out its beautiful essence, not to mention, to make it functional once more. Repurposing well-made old chairs with new paint and upholstery is an easy, inexpensive weekend project. Let’s get started.
To repaint a wood chair, you will need the following:
- Drop cloth – to keep your floors drip free
- Tack cloths – to wipe off dust and debris (paper towels/rags leave lint!)
- Mineral spirits or dish soap – the wood needs a good cleaning
- Sandpaper – 120 and 220 grit
- Sanding block – to work in those hard to reach areas
- Orbital sander – makes easy work of large areas
- Paint – buy one that can take frequent cleanings
- Foam roller and brush – these will give you a smoother finish
- Water based polyurethane – protects your paint and make clean ups easier
- Wood blocks – to position chair off floor
Tips for Successfully Painting Wood Chairs
- Prep work is key – Start by removing the seat cover. Inspect the chair’s paint condition, if it is chipped or cracked, strip it off to give the paint a smooth surface to stick to. Use a chemical stripper to bubble up the old paint and a putty knife to remove it. A heat gun can also help remove old paint. Be careful not to scrape too hard or you can damage the wood.
- Give wood a good cleaning – Clean the surface of the chair using dish soap or mineral spirits to remove any dirt or grease. Why? Contaminants cause paint not to adhere to the wood. Fill cracks and gouges with wood filler, which comes in a variety of color tints so they blend in. Let filler dry 24 hours before painting.
- When painting, go with the grain – Use 120 grit sandpaper to smooth off excess filler and to rough up the wood surface. Place the chair on the wood blocks to get it up off floor. Apply your first coat of paint, working from the top down. Paint with the grain of the wood. Allow it to dry, then use the 220 grit fine sandpaper to smooth any remaining rough spots or paint drips. Wipe the chair down completely to remove dust or debris before applying a second coat.
- Seal and protect with polyurethane – Seal the chair’s paint with polyurethane. Apply slowly and carefully, using a mini foam roller, to avoid forming air bubbles in the coating. If using a paint sprayer, hold it at least 8-12 inches away from the wood surface. Aim for multiple thin layers instead of doing one or two thick layers. When finished allow 72 hours for the chair to dry completely before using.
7 Steps for Reupholstering
- What you’ll need – cotton material for a liner and fabric for the cover.
- Remove old material and inspect the foam cushion. This may need to be replaced if too old.
- Iron out creases in both the new liner and fabric.
- Put the seat frame on the liner and trace 3 inches from the edge. Cut along this line.
- Cover the frame and cushion with the liner. Attach on the bottom at the center of each side, pulling the material tightly as you go. Work your way around, going from center to corner on each side. Fold excess material on corners, avoiding creases on the cushion top. Think hospital corners and use that staple gun!
- Once the liner is in place, repeat the same procedure with your fabric. If your material contains a pattern, place it the way you want it to be seen on top first, then flip it over to mark your lines. Pull the material tightly. Remember, staples can be removed and fabric re-adjusted.
- Once complete, you can attach the cushion back onto the chair frame.
Granny Would Be So Proud!
Now, your chair looks like a million bucks but you know the truth. Over a weekend you have managed to repurpose clutter from your attic into a serviceable piece of furniture. Feel free to take a load off and sit on your new designer chair. Granny would be SO proud!
From orbital sanders and drills to heat guns and paint sprayers, our expert staff is always on hand to help you find the right equipment to handle your home DIY project. Looking for more ideas on how to freshen up old furniture? Check out our previous blog. As always, if you have any questions about what to choose, pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.