Posts Tagged With: how to project

The Versatile Wooden Pallet – Who Knew You Could Make That?!

how to diy a pallet wine rackAh, the versatile wooden pallet! If you love to re-purpose found items, then you know about these multi-talented platforms. The internet is filled with how-tos on making everything from lawn furniture to dog houses. However, our favorite project is a wine rack with a glass holder on the bottom. It has our DIY name written all over it!

Wooden Pallets Easy to Find

Why buy lumber for your projects when you can repurpose wooden pallets? If you don’t have them on hand, check with your local stores. These shipping platforms are everywhere; you just have to look for them.

Wine Anyone?

Creating a wine rack out of a wooden pallet is easy and inexpensive. The toughest decision is what size to make it. For a small rack that will hold two to three bottles and four average sized stemmed wine glasses, you will only need to use half of a pallet.

8 Easy Steps for Building a Wooden Pallet Wine Rack

  • Cut the pallet – Use the end section for the base and cut it to the height you want. The standard width of a pallet is 40 inches so adjust it to the width you need.
  • Remove extra boards – Take two boards from the discarded portion of the pallet to use at the bottom of the rack. One board will be the bottom of the shelf where the bottles go and the other will separate the shelves.
  • Create spacers – Cut three 1 x 1 pieces to go between the bottom board for the glasses and the bottom of the wine bottle shelf. You need room to slide the glasses on and off the shelf.
  • Sand the boards – Pallet wood is notoriously rough and splintered, so use a 120 grit sandpaper for smoothing and a 220 grit paper to finish.
  • Openings for glasses – Use a jigsaw to make cuts in the bottom board for the glassware stems. Space them about 4 inches apart.
  • Assemble – Make sure your rack is sturdy by reinforcing the wine bottle shelf with an extra board. Use 2-inch nails and 3-inch wood screws to hold the board together.
  • Finishing – Stain the wood or paint it. If you choose to stain, keep in mind that sanding softens the wood and will cause it to soak up a lot of stain. Due to the rough wood, you will need to work the stain into the cracks and crevices with a cloth or brush.
  • Hanging the rack – Mount it directly into your wall studs to support the weight of the bottles and glasses. Add felt bumper pads to the backside to keep it from scuffing your wall if bumped.

Other Projects to Make with Wooden Pallets

  • Outdoor furniture like sofas and chairs
  • Patio dining table
  • Garden potting table
  • Headboard for a bed
  • Vertical wall garden
  • Dog house

Save Money and the Environment by Repurposing

Repurposing old wood from pallets helps keep them out of our landfills and saves you money. They add rustic charm to the home and garden. Stop wishing for new patio furniture or flower containers and start building what you need with wooden pallets. There are so many DIY projects to use these wooden wonders on – your Winter to-do list may stretch into Spring.

Expert Advice

From circular saws and drills to jigsaws and orbital sanders, our expert staff is always on hand to help with your next DIY home project. Still wondering what you can do with the wooden pallets around your house? Check out our previous blog, Summer Garden Update 2 – Garden Boxes Add Pizzazz to Planting, to help get those creative DIY juices flowing. As always, if you have any questions about pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Advertisements
Categories: DIY Projects, How-To's, Restore and Renovate | Tags: , , , , , , , , , | Leave a comment

8 Ways to Kick Your Backyard Up a Notch

create your perfect backyard entertaining areaWith summer in full swing, you want to entertain outdoors in a backyard that is something special. We’ve put together a list of what we think makes for a perfect outdoor entertaining area, including links to some of our past articles – see if you can’t find your next DIY project!

Big or Small, Utilize It

Whether your backyard is big or small really doesn’t matter, it’s how you utilize your space that counts. Your first task is to determine how you’ll use the entertainment area and what kind of budget you have to work with. Do you want to use your entertainment space:

  • for the kid’s pool parties?
  • for grilling with friends?
  • for relaxing with your family?
  • all of the above? 

Create Entertainment Zones

Just like rooms in your house, divide your yard up into zones – dining, entertainment, and conversation areas. See where they best fit in your landscape and tie them together into a cohesive design. Your backyard may just need tweaking in order to have it just the way you want it.

8 Elements for a Perfect Outdoor Entertaining Area

  • Water – This could be in the form of an in ground pool or maybe a backyard pond but a water feature will boost the value of your home and provide plenty of enjoyable days outside with friends and family.
  • Covered dining area – Consider installing an awning or roof to protect your mealtime from bad weather. It would extend the usability of your backyard. A covering like a pergola or fabric curtains will give the space a romantic feeling.
  • Grill – Whether it is charcoal or gas, summertime is grilling time so incorporate one into your entertainment area. Remember to give yourself storage space nearby to stash all your grilling accoutrement. Treat it like an outdoor kitchen, add a small refrigerator.
  • Deck – It moves you out of the house and into the yard. Your deck can be where your grill is located and where your dining area is. You can have different levels of a deck to include space for dining and conversation.
  • Outdoor lighting and sound system – Trying to dine by the light of an outdoor flood light can kill the mood in a hurry. Consider lights for your deck, grilling area and walkways. Add speakers to your space so everyone can enjoy the music or the big game.
  • Poolside Bar – If pool parties are your thing then having a convenient snack area close to the pool is a perfect way to extend the outdoor fun and keep wet feet out of your house.
  • Lawn and garden – Having a section of lush grass for kids to play on or a beautifully scented garden to stroll through extends your entertaining possibilities into the far reaches of your yard. Scatter conversation areas throughout your garden by adding benches and lawn furniture.
  • Outdoor fire pit – Summer always goes by so fast and installing an outdoor fire pit or fireplace can help extend your outdoor entertaining season into the fall.

Personalize Your Space with Decorations

Use decorative design elements like colorful cushions, pillows, planters and garden art to help tie your entertainment zones together. Come up with an outdoor theme that reflects you and your family’s interests – favorite sports teams, places, travel dreams or heritage, for instance.

Create the Perfect Entertainment Area for You!

Your backyard is a blank canvas for you to create the perfect entertainment area. Hopefully we have given you some ideas on how to kick your space up a notch. So get busy! Summer is calling and that grill isn’t going to light itself.

Expert Advice

From circular saws and nail guns to orbital sanders and drills our expert staff is always on hand to help with your next DIY backyard project. As always, if you have any questions about pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Categories: DIY Projects, Gardening and Lawn Care, How-To's | Tags: , , , , , , , , , , | Leave a comment

9 Tips for Building a Backyard Pond

how to make a backyard pondBackyard ponds filled with exotic fish and tranquil waterfalls are a beautiful addition to any landscape. In our previous blog, How to Build a Backyard Pond in 10 Simple Steps, we outline how to begin building a pond. Before you starting digging though, we have some tips to make this DIY project a success.

Pond Kits Give You Everything You’ll Need

The popularity of water gardening and fish ponds has grown so the supplies and the equipment you need are easy to find. Not sure what you will need? Pond kits come with all the required parts – pump, pipes and liner – and are readily available.

Bigger Ponds Are Better

If you use your own design, go bigger! The more fish and plants you have, the healthier the pond, so larger ponds actually require less maintenance. Keeping the water clean is key. Making sure you have the right size pump for your pond is important. Too small and the pump will be overworked and break down.

Pond Maintenance is a Must

A pond is very much like a swimming pool when it comes to maintenance. You will need to clean the filter frequently and remove any debris. Knowing how to service your own equipment will keep your costs down.

9 Tips for Building a Backyard Pond:

  • Buy a good liner – A good butyl rubber liner can last up to 20 years. Use carpet padding or landscape fabric underneath it for protection.
  • Avoid sharp rocks – Use smooth stones to line the pond to avoid tearing the liner. You need flat ones to line the edge.
  • Build a pond shelf – This is a partially submerged ledge where you can place plants.
  • Include rock overhangs – Give your fish places to hide and escape the hot sun.
  • Have a GFCI outlet – Plug the pump into a Ground Fault Circuit Interrupter outlet. It needs to be at least five feet away from any outdoor water.
  • Bury your electrical wires – Use PVC pipe to bury them safely in the ground and avoid having someone trip over them or an animal chew through them.
  • Consider your yard’s rain runoff – Locate the pond where it will not fill up with runoff water from your yard or a neighbor’s. Factor in an overflow stream or waterfall where the pond water can go if it does flood.
  • Add an eduction jet and skimmer – The eduction jet creates underwater currents to avoid stagnation and the skimmer will help clean of fallen leaves and debris.
  • Include a bead filter and UV Water clarifier – A bead filter traps sand and debris and a clarifier keeps algae blooms from occurring.

Landscape With A Purpose

Landscaping in and around the pond is your next big step. Select plants that will help keep the water clean and algae free. When installing your plants, use aquatic potting soil. Regular potting soil contains nutrients that will encourage algae growth. Mulch the plants with pea gravel. Start the plants on the pond ledge to acclimate them to the water. Once you have them in the right spot, then submerge them. Plants that add to your waterscape include:

  • Water moss
  • Hornwort
  • Curled pondweed
  • Lotus
  • Canna – Use in the pond or outside
  • Pitcher plant
  • Taro or Elephant’s Ear – Use in the pond or outside
  • Papyrus
  • Water Lily

Protect Your Fish

Feed your fish at least once a day during warm weather. Cut back to two or three times a week during colder weather. If you have a small pond, make sure it does not freeze solid during winter. Decaying plants release gases that get trapped under the ice and kill the fish. Install a floating deicer to keep the surface open.

Your Hard Work Pays Off

When you look back on the hard work that goes into this DIY protect and how great it turns out, you’ll be convinced that a backyard pond is a great investment for your home and a wonderfully relaxing place for your family to unwind.

Expert Advice

From backhoes and trenchers to wheelbarrows and shovels our expert staff is always on hand to help with your next DIY landscaping project. As always, if you have any questions about pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Categories: DIY Projects, Gardening and Lawn Care, How-To's | Tags: , , , , , , , , | Leave a comment

Kitchen Backsplashes with Pizazz – Creative Remodeling Project Idea #3

Remodeling Project #3 - Update Your BacksplashYou want to add a little pizazz to your kitchen – how about starting with that often overlooked area called the backsplash? It’s a design opportunity just waiting for an inspired DIY’er like yourself. Get those creative juices flowing, we’ve got work to do.

Make it Take the Heat and the Mess

There is a wide range of materials available for your backsplash. Choose a material that will complement countertops or add overall warmth to the kitchen. Keep in mind the product you choose needs to be able to withstand heat, greasy splatters and frequent cleanings. A few popular options are:

  • Ceramic tile – Widely available and affordable
  • Metals – Stainless steel, copper, tin
  • Glass – Tiles or solid panels
  • Stone – Granite, marble, soapstone, quartz
  • Metallic penny tiles
  • Wood
  • Laminate

Subway Tiles: An Elegant, Affordable Choice

One of the most popular (and affordable) options is subway tiles. They come in a variety of colors and sizes and are easy to install. Give your backsplash additional interest by laying the tile at an angle or in a pattern. Here are a few tips on installing tile:

  • Prepare your work area – remove outlet covers and any fixtures, cover your countertops and tape off around cabinets.
  • Use cement backer board – this is actually a thin layer of concrete with fiberglass weave on both sides, which gives the tile something firm to sit on.
  • Apply tile mastic to small section of wall – this is a ready-to-use adhesive that has better adhesive properties on vertical surfaces than thin set.
  • Cut and place tiles – work in small areas so the mastic does not dry. Use spacers.
  • Apply grout – allow tiles to set overnight before applying grout. You can use tinted grout if you don’t want white.
  • Clean and caulk – wait at least 30-40 minutes for the grout to set before wiping the tiles clean with damp sponge. Caulk where the tiles meet the countertop.

Personalize Your Kitchen Backsplash

If tile and traditional materials aren’t what you are looking for, then consider non-traditional DIY options that add personality:

  • Customized wallpaper – Photographs, quotes or textured fabrics applied to the walls with adhesive and covered with glass.
  • Install a mirror – A reflective surface can open up a small space and show off countertops.
  • Paint – If you already have a tile backsplash, give it a pop of color with paint.
  • Ceiling tiles – Laminated thermoplastic panels can be glued to walls to give an old world feel.
  • Repurposed wood – Reuse old wood flooring, apply varnish and seal to make for easy clean-up.
  • Cork – Glue squares of this on the walls for a handy recipe/reminder board for the whole family. Seal it for easy wipe downs.

Spice Up Your Kitchen with A New Backsplash

Whatever material you choose, updating your backsplash is an easy, economical way to breathe life back into your kitchen. Get creative and spice up your galley this weekend. It’s a little change that reaps big results.

Expert Advice

From masonry saws to tile nippers and cutters, our expert staff is always on hand to help you find the right equipment for your next kitchen update. Is this your first time installing tile? Learn helpful tips from our blogs, How to Install a Kitchen Tile Backsplash and How to Cut Tile for Do-it-Yourself Tiling Jobs. As always, if you have any questions about what to choose, pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Categories: DIY Projects, How-To's, Restore and Renovate | Tags: , , , , , , , , , | 1 Comment

Give Old Chairs New Life with Fresh Paint & Upholstery

How to Reupholster ChairsWhile cleaning out the attic (a New Year’s resolution, perhaps?) you come across a pair of your grandmother’s old chairs. You realize that with a fresh coat of paint and new fabric, you can breathe life back into them – and they would be perfect for your home. Congratulations, you have just found your next DIY project!

Good Bones Are Good Bones

Furniture left languishing in attics and storage closets just needs a little TLC to bring out its beautiful essence, not to mention, to make it functional once more. Repurposing well-made old chairs with new paint and upholstery is an easy, inexpensive weekend project. Let’s get started.

To repaint a wood chair, you will need the following:

  • Drop cloth – to keep your floors drip free
  • Tack cloths – to wipe off dust and debris (paper towels/rags leave lint!)
  • Mineral spirits or dish soap – the wood needs a good cleaning
  • Sandpaper – 120 and 220 grit
  • Sanding block – to work in those hard to reach areas
  • Orbital sander – makes easy work of large areas
  • Paint – buy one that can take frequent cleanings
  • Foam roller and brush – these will give you a smoother finish
  • Water based polyurethane – protects your paint and make clean ups easier
  • Wood blocks – to position chair off floor

Tips for Successfully Painting Wood Chairs 

  1. Prep work is key – Start by removing the seat cover. Inspect the chair’s paint condition, if it is chipped or cracked, strip it off to give the paint a smooth surface to stick to. Use a chemical stripper to bubble up the old paint and a putty knife to remove it. A heat gun can also help remove old paint. Be careful not to scrape too hard or you can damage the wood.
  1. Give wood a good cleaning – Clean the surface of the chair using dish soap or mineral spirits to remove any dirt or grease. Why? Contaminants cause paint not to adhere to the wood. Fill cracks and gouges with wood filler, which comes in a variety of color tints so they blend in. Let filler dry 24 hours before painting.
  1. When painting, go with the grain – Use 120 grit sandpaper to smooth off excess filler and to rough up the wood surface. Place the chair on the wood blocks to get it up off floor. Apply your first coat of paint, working from the top down. Paint with the grain of the wood. Allow it to dry, then use the 220 grit fine sandpaper to smooth any remaining rough spots or paint drips. Wipe the chair down completely to remove dust or debris before applying a second coat.
  1. Seal and protect with polyurethane – Seal the chair’s paint with polyurethane. Apply slowly and carefully, using a mini foam roller, to avoid forming air bubbles in the coating. If using a paint sprayer, hold it at least 8-12 inches away from the wood surface. Aim for multiple thin layers instead of doing one or two thick layers. When finished allow 72 hours for the chair to dry completely before using.

7 Steps for Reupholstering

  1. What you’ll need – cotton material for a liner and fabric for the cover.
  2. Remove old material and inspect the foam cushion. This may need to be replaced if too old.
  3. Iron out creases in both the new liner and fabric.
  4. Put the seat frame on the liner and trace 3 inches from the edge. Cut along this line.
  5. Cover the frame and cushion with the liner. Attach on the bottom at the center of each side, pulling the material tightly as you go. Work your way around, going from center to corner on each side. Fold excess material on corners, avoiding creases on the cushion top. Think hospital corners and use that staple gun!
  6. Once the liner is in place, repeat the same procedure with your fabric. If your material contains a pattern, place it the way you want it to be seen on top first, then flip it over to mark your lines. Pull the material tightly. Remember, staples can be removed and fabric re-adjusted.
  7. Once complete, you can attach the cushion back onto the chair frame.

Granny Would Be So Proud!

Now, your chair looks like a million bucks but you know the truth. Over a weekend you have managed to repurpose clutter from your attic into a serviceable piece of furniture. Feel free to take a load off and sit on your new designer chair. Granny would be SO proud!

Expert Advice

From orbital sanders and drills to heat guns and paint sprayers, our expert staff is always on hand to help you find the right equipment to handle your home DIY project. Looking for more ideas on how to freshen up old furniture? Check out our previous blog. As always, if you have any questions about what to choose, pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Categories: DIY Projects, How-To's, Restore and Renovate | Tags: , , , , , , | Leave a comment

DIY Project: How to Install a Sump Pump

How to Install a Sump PumpHaving a flooded basement is one of the worst fears a homeowner has and it’s a costly one. It only takes a heavy rainfall or a broken water pipe to ruin everything in the lower level of your home. One item that can alleviate this anxiety is a sump pump.

Water Problems are Not Uncommon

Sixty percent of American homes suffer from below-ground wetness. Water problems can be caused by:

  • Excessive water, i.e. over-saturating the ground around the foundation
  • Improperly installed or maintained gutters
  • Patios, decks or walkways sloping back toward the home’s foundation

Which Type of Sump Pump Do You Need?

Installing a sump pump in your basement is an easy do-it-yourself project. A sump pump’s main function is to channel water out of your basement and away from your foundation. There are three different types of pumps:

  • Pedestal – This type has the motor mounted above the sump pit and is less expensive. They can last 25-30 years but take up more room and cannot handle debris.
  • Submersible – The motor is submerged in the sump pit, which makes it less accessible. These pumps last 5-15 years, are best for tight spaces and can take up debris without clogging the pump.
  • Ejector – These are good for crawlspaces with pea gravel floors. Constructed from cast iron, these pumps last between 5-10 years and can eject small debris as well as water.

Installing a Sump Pump is Easy

Before you begin to dig the sump pit (the hole in which the pump sits), know where your main water and power lines are. It is recommended that you buy your sump pump and the heavy plastic pit liner together to assure proper fit. Once you determine the lowest point in your basement, we are ready to begin.

  1. Place the pit at least 8” away from outside walls, but close to a GFCI (ground fault circuit interrupter) electrical outlet. You need to plug directly into outlet. No extension cords please!
  2. Dig a hole that is 3” wider than the liner and 6” deeper. You will need to jack hammer the foundation floor in order to clear the way for digging.
  3. Line the pit with gravel at the bottom and tamp. Place and level the liner inside the pit and fill around it with more gravel.
  4. Attach the discharge pipe to the pump and place it in the pit, making sure to keep it level. The discharge pipe is usually made of PVC pipe and will run from the pit to the outside of the house. A common method of getting the pipe outside is to drill into the rim joist.
  5. Dry fit all pipes together and then cement. Discharge pipes should have a small vent hole to prevent an air lock from forming. Be sure to caulk around the pipe, exiting through the rim joist.
  6. Dig a hole about a foot deep for the discharge line to exit through. Fill the hole completely with gravel to keep the line from freezing.
  7. Support the PVC pipes by attaching them to walls or other joists.
  8. Adjust the float valve on the pump and test. Pour water into the pit until the pump is submerged. Plug the pump in and voilà! Water is exiting the building.
  9. Put a cover or lid over the pit to help keep debris from getting into the pump or it becomes a hazard.

Consider Buying an Alarm and Battery Back-Up

You should consider buying a pump that has an alarm and a battery back-up. Both would come in handy during storms when water is likely to be a problem. For frequent flooding problems, you may want to consider having two separate sump pumps just to cover you in the event the first one fails.

Inspect and Test Your Pump Regularly

It is a good practice to test your sump pump twice a year. Just fill the pit with water and turn the pump on. Regular inspection of the pump will help you avoid any issues. To learn more about some of the potential problems you can face check out our blog on repairing sump pumps.

Keep Your Home Safe and Dry

You no longer have to worry about a flooded basement with a sump pump. This simple DIY project will help keep your home safe and dry. So sleep easy and listen to the rain. You’re in good hands.

Expert Advice

Our expert staff is always on-hand to help you with your DIY projects. From jack hammers and drills to shovels and tamps, if you have any questions about what to choose, pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Categories: DIY Projects, How-To's, Restore and Renovate | Tags: , , , , , , | 1 Comment

[DIY How-To] Repurpose Your Dead Trees Into Mulch & Firewood

how to repurpose dead and fallen tree limbs

Are your trees healthy? Even though fall is typically not the season to prune your trees, which encourages growth or flowering next spring (this is usually done after the coldest winter weather has passed), it is a perfect time to assess the health of the trees on your property. Removing dead limbs won’t encourage growth, and will help eliminate potential problems brought on by inclement weather. It will also provide you with ample mulch and firewood for the long cold months ahead.

Remove Tree Limbs

  • to get rid of diseased parts and save the tree
  • to avoid personal injury or property damage
  • to cut back overgrowth

Start at the Top

Look for tree hazards by scanning the tree from top to bottom. Use binoculars if needed and check how vigorously the tree is growing. Compare its growth to others around it. Vigor is reflected in the amount of leaf cover, leaf size, color and condition. If the tree seems to be thinning or experiencing stunted growth, then it may not be flourishing as robustly as it should.

How Does the Trunk Look?

Continue your examination down the trunk of the tree. Look for forked trunks, which indicate potential weaknesses. Signs of decay may also be evident. These present themselves as cavities, cankers or conks (fruiting bodies of fungi) on the trunk itself.

Getting to the Bottom

Finally, check root zone of the tree. Look for mushrooms and other fungi that might be growing around the base of the tree. This is a sign the tree roots may be decaying. Construction and trenching are often causes of root damage, so protect your trees when work is done near them.

Make Your Cut Count

Pruning dead limbs is necessary to keep you and your property safe and it needs to be done properly. Make clean cuts with sharpened tools. Look for the “collar” or swollen tree flesh that develops where the dead limb joins the healthy section of tree. This is the tree’s natural defense system. Make your cut using a pruner or a chain saw just outside the collar, leaving as little stub as possible. Do not remove the collar because it is needed to fight any remaining disease.

Making Mulch and Firewood

Once you have examined your trees and removed the dead limbs, recycle the debris into mulch or firewood. Using a wood chipper, you can make easy work of breaking it all down. The size of the tree limbs determines the size of the chipper you will need. You can mix grass clippings in with your grind or even run the mixture through the chipper twice to get a finer mix. For larger tree limbs or stumps use a log splitter to cut the debris down to a usable size for the fireplace.

“Snag” a Place for Wildlife to Live

Food for thought – if a dead or dying tree does not pose a hazard to people or property – why not leave it as part of your landscape? “Snags” or wildlife trees are excellent habitats for a variety of species of animals. Birds and small mammals use snags for nests or storage areas. Woodpeckers feed off the insects in them and hawks use them as perches for hunting. Snags can also be created from living trees. An arborist would be able to help you select a good candidate for a snag in your yard. Snags provide hours of wildlife watching.

Expert Advice

Our expert staff is always on hand to help you with all of your landscape projects. Check out some of our blog posts on how to remove a dead tree for more information on tree cutting, as well as a list of tools you might want to use in getting rid of tree limbs and trunks. If you have any other questions about what to choose, pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Categories: DIY Projects, Gardening and Lawn Care, How-To's | Tags: , , , , , , , | Leave a comment

How to Build a Backyard Pond in 10 Simple Steps

how-to build a backyard pondOne sure way to add a beautiful focal point to any landscape is to introduce a water feature. What about building a backyard pond? It will not only add diversity, it attracts beneficial wildlife. Adding a small pond with trickling water is an easy weekend project, plus you and your family will enjoy it for years to come.

Keep it Close

To get the maximum enjoyment from your pond, keep it close to your home. You want to see and hear it from your windows or patio area. Because you need electricity for the pump, keep the pond within close proximity to an outdoor outlet. Most pumps come with a 24-foot power cord; any further than that and you will need to extend your power lines.

Not Too Much Sunlight, Please

Ponds need sunlight to support beneficial wildlife and they prefer partial daily exposure. Too much sun can warm the water too much and allow algae to thrive. Avoid positioning your pond near large trees. Roots can damage your lining in their quest for moisture. Besides, fishing leaves out of your pond all the time is no fun.

Habitat for Fish?

Do you want a fish pond? You and your family may enjoy taking care of fish. However, they will need to be fed daily and the pond filter will need to be cleaned or changed regularly. It’s a decision to make before committing to be “fish parents.” If you commit, build in water depth to the pond, which is more critical than circumference. You need to dig a minimum of 18 inches for goldfish and three feet for koi in order for them to survive the winter.

The Soothing Sounds of a Waterfall

Consider adding a waterfall to your pond. Keeping the water moving and aerated helps keep algae in check and prevents mosquitoes from laying eggs. Flowing water also attracts birds and other interesting wildlife. Plus you benefit from the soothing sounds yourself.

Time to Start Digging

Now that you’ve decided where and how large of a pond you want, it’s time to call 811 to have someone come out and determine where underground gas and electrical lines might be. Once you’re clear of that, it’s time to start digging.

  • Mark the outline – form the shape you want with twine or landscape paint.
  • Excavate the area – if you are going for a lovely large water feature you may want to consider using a Bobcat or an excavator to make your digging easier.
  • Terrace the pond
  • Create a 3-inch wide area around the outside of your outline for the stone border.
  • Create a 1-foot wide shelf around the inside of the outline for aquatic plants. It should be about 8 inches deep from the edge of the pond.
  • Dig the bed of the pond a minimum of 18 inches deep, sloping slightly in creating the walls.

4) Dig a trench back to the power supply – this should be close to the deepest part of the pond since that is where the pump will go.

5)   Add an overflow trench at one end of pond – It should be about 6 inches wide and 1 inch deep to help channel overflow caused by heavy rains away from your pond.

6)   Prepare the Base – Add a 1 inch layer of sand followed by a 1/2” layer of newspapers around the entire base of the pond and terrace areas. The newspaper will help protect the liner from punctures.

7)   Line the Pond – Use a polypropylene flexible liner that can withstand UV rays, freezing temps, and is rated “fish friendly”. Cut the liner about 4 feet wider and longer than the pond dimensions. Center the liner in the pond and press it down, pushing tightly into the crevices.

8)   Fill the Pond – Begin adding water to the pond using a garden hose. While the pond is filling up pull the liner tightly to help remove creases. Get someone to help with this so that the extra liner you’ve left over the pond edge will not shift.

9)   Install the pump – Thread the power cord through a PVC pipe and place it in the trench leading back to exterior outlet and backfill. Place the pump in the deepest section of the pond while holding onto the other end of the hose.

10) Create a Rock Border – To hide the liner edge place rocks around the perimeter. The rocks need to interlock so they will not be loose and cause a safety hazard. Create easy access for wildlife by extending some of the rocks into the shallow water.

Jump Start Your Pond’s Ecosystem

Landscaping inside and around your pond is important for completely the look of your water feature. It helps to attract wildlife like birds and butterflies, and looks pretty to the human eye, too. To jump start your pond’s ecosystem add a bucket of water from a nearby natural water source. It will introduce millions of organisms and help keep your pond’s health in balance with nature.

Expert Advice

Our expert staff is always on hand to help you with your landscaping projects. From Bobcats and excavators to shovels and wheel barrows, if you have any questions about what to choose, pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Categories: DIY Projects, Gardening and Lawn Care, How-To's | Tags: , , , , , , , , | 4 Comments

Create a free website or blog at WordPress.com.

%d bloggers like this: