Posts Tagged With: home maintenance

Easy Advice for Installing Storm Windows = Big Energy Savings This Winter

How to Install Storm WindowsWorried about winter heating bills? Or just wishing your home wasn’t so drafty? We’ve already covered the perfect DIY solution #1: installing storm doors. What’s the perfect DIY solution #2? Installing storm windows. They alone can save you between 12 and 33 percent on your heating costs and are much cheaper than replacement windows. Plus, installing storm windows is easy, with our expert how-to advice.

Make Your Choice – Interior or Exterior Storm Windows

Determine what type of storm windows you’d like – interior or exterior. Exterior models come with solid windows and screens in frames that attach directly to an existing window. Interior storm windows are usually seasonal products that you install every winter. They snap or clip into your interior windowsill but do not have adjustable glass panes or screens.

Exterior storm windows are the most common. Frames are made from wood, aluminum or vinyl and offer extra protection to your existing windows. They help them last longer and require less maintenance to the paint and caulk. Most have low emissivity glass (Low-E), which keeps thermal heat in during the winter and infrared heat out during the summer.

Installation is a simple DIY home project that you can tackle in a weekend (depending on the number of windows you have). To start, you will need the following:

Measure, Measure, Measure

Take a series of measurements of the inside of your existing window, at the bottom, top and middle of the frame. Why? The window frame may not be straight. Use the smallest measurement to order your storm windows. Measure the height of the frame from the outside of your window.

Consider ordering your windows with some of the following features:

  • Multiple positioning stops so you can raise or lower the panes to where you want.
  • Quality weather stripping to help stop heating/cooling loss.
  • Pre-drilled holes for quicker installation.
  • Easy-to-clean removable half pane glass and screens to make spring cleaning easier.

Drill Weep Holes then Paint

Storm windows come with weep holes installed at the bottom. Drill matching holes in the bottom exterior windowsill. This will allow condensation to escape. Next, scrap and paint the exterior frame before installing the new window.

Seal Your Storm Windows

Manufacturers recommend applying Butyl caulk, a rubber-based sealant that is good for outdoor installations like siding and gutters. It is a little uncooperative to work with, but it seals better than a silicone caulk. Apply it to the back of the storm window before installing to the exterior frame.

An Extra Set of Hands Comes in – Handy

You may need an extra set of hands to help hold the storm window while you mount it. First center the window then screw it in at top. Close the bottom sash and then screw the sides to the exterior frame. There will be an adjustable expander at the bottom of your storm windows. Tap it down tight against the windowsill and you are done.

Look for Condensation and Fix Air Leaks

Be sure to check your storm windows for condensation during the next cold snap. Leaks from your interior windows can cause moisture build up. This is no problem since the storm window has weep holes, but you may want to follow up with new weather stripping on your interior sill to plug possible air leaks.

Take a Bite Out of Your Next Power Bill

Cutting down on heating bills is always a challenge. Improving your home’s insulation, plugging air leaks and installing storm windows will go a long way to take a bite out of that next bill. Next time the cold wind blows and you sit warm inside, remember to thank your storm windows. Everyone likes a nice pat on the back from time to time.

Expert Advice

From ladders and drills to caulking saws, our expert staff is always on hand to help you find the right equipment to tackle your next DIY project. For more helpful tips on how to keep things warm at your house check out our blog, 3 Easy Economical Ways to Winterize Your Home. As always, if you have any questions about what to choose, pricing or how-to’s, don’t hesitate to contact us. Stop by our store — we’re open seven days a week.

Categories: DIY Projects, How-To's | Tags: , , , , , , , , | 1 Comment

Make Doors Look New Again with 2 Fast and Easy In-Home Repairs

There’s no better time like the present to roll up your sleeves and find out how you can complete home improvement projects and repairs yourself. All you need is a plan and the right tools for each job. Besides taking care of nagging repairs like a leaky faucet, you’ll increase the beauty of your home with fast and easy in-home repairs, like refurbishing your doors.

Repair Your Doors

1. Refurbishing Interior Doors

Interior doors are usually made from wood and can be susceptible to seasonal changes in climate, which can cause squeaks or sticking. They also can be scratched from usual wear and tear.

What to Do:

  • Inspect the hinges for deterioration or loose screws.
  • If hinges look oxidized, add a lubricant to alleviate squeaks; work the lubricant into the hinge by opening and closing the door after application.
  • If the hinges are caked with old lubricant or dirt, tap out the pins with a hammer and screwdriver and clean with steel wool, then clean the pinholes with a small circular wire brush. Remember to place a shim under the door for support.
  • If screws are loose, place a wedge on the latch-end of the door for weight balance before tightening with a screwdriver.
  • If a door continues to stick, use a planer to scrape a small layer of wood off the offending edge:
    • Draw a line on the door at the spot where it’s hitting the jamb
    • If that spot is at the top or on the handle end, you can plane the door without taking it off its hinges. If the tight spot is on the hinge end or at the bottom, take the door off its hinges and set it on its side to plane.
    • Inspect the door surface for scratches.
    • Fill any scratches with door filler, such as a pencil, crayon or felt-tip pen-type product found at many local hardware stores. Find the shade that most closely matches your door and rub it into the scratch.

2. Restore a Front Door

Exterior doors are made from wood or metal and are usually exposed to the elements. After years of wind, sun, heat and precipitation, your front door and all its hardware may need an upgrade.

What to Do:

  • Inspect the door, hinges and hardware for damage, wear and tear.
  • If repair is required, take the door off its hinges and remove the hardware.
  • Place the door on saw horses and lay down drop cloths.
  • Strip off old paint. While latex paint may need a chemical paint stripper for this job (work outdoors or make sure you work indoors with adequate ventilation), most paint can be removed using putty knives, paint scrapers, sandpaper and a hand-held sander or belt sander.
  • If you want to finish the door as natural wood, remove all the paint, sand thoroughly and apply a natural product like mineral oil. If you’re re-painting the door, sand roughly until the door is smooth and ready for paint, removing all dust from the surface.

Be sure to stay tuned for two more posts similar to this one, part of our 3-part in-home repair series! And for questions or comments concerning this post, contact us or use the comment section below. Happy door maintaining!

About the Author

Tempe Thompson is a sales and inventory expert at Runyon Equipment Rental. She has over 35 years of experience and has accumulated a tremendous amount of knowledge and expertise. She could talk for hours about how to use all of Runyon’s tools and equipment, in addition to suggesting which type corresponds to a certain application.

Categories: How-To's, Restore and Renovate | Tags: , , , , , , , , , , | 1 Comment

Be Sure You Have a Snow Blower this Winter – a True Must-Have Item

It’s been a strange winter thus far, with warm weather and exceedingly cold weather. Have you adjusted well to the changes, especially the snow? Besides considering a portable generator, a snow blower is another essential piece of winter equipment to have handy. So find out everything you need to know about the second item on your winter must-have list:

  1. Portable Generator
  2. Snow Blower
  3. Outdoor and Indoor Heaters
  4. Ice Melt

In this post, we’ll explore the benefits of the Snow Blower.

One of several DIY solutions for efficient snow removal, the snow blower, could be one of the most loved power tools in your garage! Why? If shoveling is physically impossible or you’re not going to hire someone else to shovel, using a snow blower can save you a lot of time and sweat equity.Use a snow blower

Choose the right snow blower for the job. First, you’ve got to identify your “snow removal profile” – how much snow you need to clear from how large an area. Then, take into consideration what the terrain is like and what kind of snow is falling, most of the time. Will you be pushing the snow blower up a slope, or running it right down the driveway in a straight, level line? Is the snow wet, icy, powder or in-between? All of these factors come into play while you’re pondering in the snow blower isle at the store.

Snow blowers come in three types: single-stage electric,  single-stage gas and two-stage gas. More than one of these types may be able to handle your typical snow-clearing job.

Single-Stage Snow Blowers

  • Lighter
  • Easier to handle
  • Best in light snowfalls of eight inches or less
  • Great for clearing small to medium-sized areas
  • Best for paved surfaces

Electric single-stage models tend to be lighter and more compact that gas units. They start with the push of a button and require an outdoor extension cord to operate. Larger gas-powered single-stage snow blowers on the other hand, are not tethered to a power cord, and typically can clear wider, higher areas.

Two-Stage Snow Blowers

  • A larger engine and intake area clears more snow faster
  • Best in medium to heavy snowfalls in excess of eight inches
  • Great for driveways over 60 feet
  • Two-stage operation prevents clogging in heavy, wet snow
  • Cut through hard-packed snow or ice

Some two-stage snow blowers have engine-driven wheels that can handle uneven or sloped terrain. The push-propelled models are best for level surfaces. You can also use tire chains with some models for more traction in all conditions. Chances are, you’ll still need to shovel around parked cars and for finishing work.

Don’t forget a gas can! Easy-to-use, spill-proof gas cans are ideal to keep on hand for fueling gas-powered tools like snow blowers.

About the Author

Tempe Thompson is a sales and inventory expert at Runyon Equipment Rental. She has over 35 years of experience and has accumulated a tremendous amount of knowledge and expertise. She could talk for hours about how to use all of Runyon’s tools and equipment, in addition to suggesting which type corresponds to a certain application.

Categories: Choosing Equipment, Featured Products, How-To's | Tags: , , , , , , , , , , | 1 Comment

Create a free website or blog at WordPress.com.

%d bloggers like this: